Why Electronic Sensors Struggle in Extreme Environments
How Fiber-Optic Sensors Measure Touch, Strain, and Force
Fiber Bragg Gratings for Robotic Touch
Intensity-Based Sensing as a Simpler Alternative
Radiation Effects on Optical Fibers
Integration Challenges
Conclusion
References and Further Reading
Robots perform maintenance, inspection, and decommissioning tasks in nuclear plants, particle accelerators, and fusion facilities where human workers face serious health risks. These robots use sensors to hold objects and detect collisions safely.
Image Credit: Hadayeva Sviatlana/Shutterstock
However, ionizing radiation and strong electromagnetic fields can interfere with traditional electronic sensors. This article discusses the challenges electronic sensors face in these environments, how fiber-optic sensors can measure touch, strain, and force, and which hurdles limit their adoption.1
Why Electronic Sensors Struggle in Extreme Environments
Radiation can damage the electronics in robots during their missions. A recent study in Nuclear Engineering and Technology exposed microcontrollers, servo motors, and temperature sensors to dose rates ranging from 0.09 to 1.5 gray/s. It tracked the response of a three-degree-of-freedom robotic arm. The study also found that electronics are a weak spot, leading to unexpected failures and premature termination of robotic operations.1
Engineers protect these circuits with radiation-hardened chips or heavy shielding, and both options carry costs. Hardened components come from a limited and tightly regulated catalog. Studies on nuclear robots have shown that these chips are expensive and still lack guaranteed reliability. Shielding improves survival and adds weight to arms and grippers. Electromagnetic fields near motors and high-voltage equipment also add noise to wires carrying analog signals.1,2
How Fiber-Optic Sensors Measure Touch, Strain, and Force
Fiber-optic sensors carry their measurements as light through thin, flexible strands of glass or plastic. The fiber is a dielectric material, immune to electromagnetic interference and incapable of producing sparks, making it intrinsically safe in hydrogen-rich spaces. Aircraft such as the Boeing 777 have relied on optical fibers for onboard data communication since the 1990s.3
The same physics allows engineers to separate the sensing point from the electronics that read it. In a fiber Bragg grating system, only the grating responds to the measured quantity. As a result, the interrogator that decodes the signal can sit safely outside the radiation zone. The robot carries passive glass inside its fingers and skin, and vulnerable circuitry stays where technicians can shield and service it.3
Fiber Bragg Gratings for Robotic Touch
A fiber Bragg grating is a short section of fiber with a periodic pattern written into its core. The pattern reflects one narrow band of wavelengths. When the fiber stretches or compresses, the reflected wavelength shifts by about one picometer per microstrain in commercial gratings. Gratings with different periods can share a single fiber, so a daisy-chained strand requires one connector, whereas a single-axis electrical strain gauge requires three.3
Turning that strain response into a sense of touch requires careful mechanical design. A study published in MDPI Sensors embedded a single grating 1 mm deep inside polydimethylsiloxane, a soft silicone resembling human skin. A square hole beneath the grating channeled fingertip pressure into axial strain and cut interference from sideways forces from 11.21% to 7.63%. That gain lowered sensitivity from 8.85 to 3.48 pm/N.4
Arrays of gratings enhance this concept, expanding its application from fingertips to robotic skin. As reported in Advanced Intelligent Systems, scientists integrated 4 gratings within a 3-layer laminate that can stretch over 20%. With machine learning interpreting the signals, the sensor can be used. A similar type of skin could enable a robotic manipulator to detect unintentional contact along its arm.5
Intensity-Based Sensing as a Simpler Alternative
Intensity-based fiber sensors measure how much light survives the trip through a fiber. Pressing or bending the fiber causes some light to leak out, and a photodetector reads the resulting drop in power. A work published in the journal MDPI Fibers wound a polymer optical fiber into an 8-shaped ring inside silicone. Pressing the surface tightened the ring and increased the bending loss, resulting in a signal change of 2.16 dBm/N.6
The main attraction of this approach is its inexpensive and simple optoelectronic hardware. The setup uses a white light-emitting diode (LED), a plastic fiber, and a power meter, and it requires no spectral analysis. The authors report a response time of about 0.4 seconds and stable output over 216 loading cycles over 12 hours. They also record hysteresis due to stress relaxation in the polymer and a nonlinear relationship between force and light loss.6
Radiation Effects on Optical Fibers
Glass fibers face their own vulnerabilities once radiation enters the picture. Radiation creates defects that absorb light, a phenomenon known as radiation-induced attenuation. In a standard telecom fiber, the loss at 1550 nm can increase from 0.2 to 2,000 dB/km within tens of nanoseconds of radiation exposure. For an intensity-based sensor, this darkening resembles a strong press, and the force readings become ambiguous.3
Fiber Bragg gratings handle this problem better because they encode information in wavelength, which remains readable as long as enough light returns to the interrogator. Radiation can still shift the reflected peak, and a pure-silica-core grating moved by about 20 pm after a 100-kilogray dose. Fluorine-doped fibers, already used in the International Thermonuclear Experimental Reactor (ITER) plasma diagnostics and the Large Hadron Collider (LHC) data links, maintain radiation-induced losses below 5 dB/km.3
Integration Challenges
Moving these sensors from laboratory benches onto working robots exposes several engineering problems. Gratings respond to temperature at roughly 10 pm/oC. Therefore, a 1oC change produces the same shift as about 10 microstrain. Reliable designs need temperature compensation, often via a second, strain-free grating that tracks temperature alone so the software can subtract its signal.3
Download the PDF of this page here
Mechanical durability poses a second hurdle for fiber-based robotic hands. Glass fibers can break when the finger joints bend sharply. To address this, designers can place several gratings in series across the knuckles and capture their readings through wavelength-division multiplexing.
The performance is also influenced by packaging; for instance, a grating embedded without pre-tension yields lower sensitivity than models predict. Additionally, multiplexing can be costly, especially when long fiber lengths necessitate monitoring, increasing expenses for larger robots.3,4
Conclusion
Fiber-optic sensors give robots in extreme environments a way to sense contact and strain while keeping fragile electronics away from the measurement point. Fiber Bragg gratings offer precision, multiplexing, and wavelength-coded signals that tolerate radiation, whereas intensity-based designs trade accuracy for low cost and simplicity. Once engineers solve temperature drift, fiber fragility, and packaging, light-based touch can become standard equipment for robots entering places people cannot go.
References and Further Reading
- Coloma, S. et al. (2023). The effect of ionizing radiation on robotic trajectory movement and electronic components. Nuclear Engineering and Technology, 55(11), 4191-4203. DOI:10.1016/j.net.2023.07.041. https://www.sciencedirect.com/science/article/pii/S1738573323003583
- Chang, Y. et al. (2024). Research on Radiation Damage and Reinforcement of Control and Sensing Systems in Nuclear Robots. Electronics, 13(7), 1214. DOI:10.3390/electronics13071214. https://www.mdpi.com/2079-9292/13/7/1214
- Rovera, A. et al. (2023). Fiber Optic Sensors for Harsh and High Radiation Environments in Aerospace Applications. Sensors, 23(5), 2512. DOI:10.3390/s23052512. https://www.mdpi.com/1424-8220/23/5/2512
- Lu, G. et al. (2023). Research on Finger Pressure Tactile Sensor with Square Hole Structure Based on Fiber Bragg Grating. Sensors, 23(15), 6897. DOI:10.3390/s23156897. https://www.mdpi.com/1424-8220/23/15/6897
- Li, T. et al. (2023). An Artificial Intelligence-Motivated Skin-Like Optical Fiber Tactile Sensor. Advanced Intelligent Systems, 5(8), 2200460. DOI:10.1002/aisy.202200460. https://advanced.onlinelibrary.wiley.com/doi/10.1002/aisy.202200460
- Liu, Y. et al. (2025). A High-Flexibility Contact Force Sensor Based on the 8-Shaped Wound Polymer Optical Fiber for Human Safety in Human–Robot Collaboration. Fibers, 13(2), 15. DOI:10.3390/fib13020015. https://www.mdpi.com/2079-6439/13/2/15
Disclaimer: The views expressed here are those of the author expressed in their private capacity and do not necessarily represent the views of AZoM.com Limited T/A AZoNetwork the owner and operator of this website. This disclaimer forms part of the Terms and conditions of use of this website.